Bb-electronics ABDN-ER-IN5018 - Quick Start Guide Uživatelský manuál stáhnout pdf

http://www.bb-elec.com/Products/Wireless-

Cellular/AirborneM2M-Embedded-Dual-Band-

Wireless-Module/AirborneM2M-Embedded-Dual-

Band-Access-Point-Module.aspx

APXG-Q5420

802.11 Wireless Router, Access Point and

Serial Device Server

http://www.bb-elec.com/Products/Wireless-

Cellular/Wireless-Ethernet-Bridge-Access-Point-

Client-Bridg/Airborne-Industrial-Wireless-Access-

Point.aspx

Document number – PN710-00050-00_R000_ABDx-ER-IN50xx_1413qsg

1-888-948-2248 | Europe: +353 91 792444

www.bb-elec.com

707 Dayton Road | PO Box 1040 | Ottawa, IL 61350

Phone: 815-433-5100 | Fax: 815-433-5109

www.bb-elec.com | E-mail: [email protected]

Fast and easy on the web:

www.bb-elec.com

First Things First...

Before you begin, be sure you have

the following:

Industrial Wireless Ethernet Adapter

Fast, Easy Answers

ABDx-ER-IN50xx

Continuing section 6

Use the Help features of the interface to help you

conﬁgure the device. When you are done with

conﬁguring the device, press ‘Commit’ to save the

changes, then ‘Restart’ to restart the device. You

can optionally press ‘Reload’ if you have further

conﬁguration changes to make.

Check Your Setup

If your device is connected and conﬁgured correctly, you

will see the following LED Status:

COMM: GREEN

LINK: GREEN

POST: GREEN

POWER: BLUE

Troubleshooting

LED Airborne Device State

POWER

Adapter is not powered.

Adapter is powered

POST

Adapter is not powered.

Adapter failed Power On Self Test (POST) and is not conﬁg-

ured for wireless communication.

Adapter passed POST but is not conﬁgured for wireless

network communication.

Adapter passed post and is conﬁgured for wireless com-

munication.

LINK

Adapter is not powered.

(Periodic Blinking) Adapter is searching for a valid network

(Access Point) that matches device’s conﬁguration.

Adapter has successfully associated with an Access Point.

COMM

If Power LED is also Off then Adapter is not powered.

If Power LED is On then: No TCP session from WLAN or

Ethernet interface has been established.

A TCP connection to the adapter has been established from

the Wireless or Ethernet interfaces but no trafﬁc has been

detected.

First, check your LEDs.

Then use your smart

phone to access complete

documentation on our web

site. Simply scan the code

to the right or visit the

B&B Electronics Knowledge

Base:

http://support.bb-elec.com/knowledgec.aspx

ABDx-ER-IN50xx

CD with Airborne Management Center

software

5-36 VDC power for terminal block

or a 5 VDC Power Supply (not included)

50 ohm, omni-directional antenna

APMN-Q551

Embedded Dual Band M2M Access

Point Module

More AirborneM2M Products

1 2

ABDx-ER-IN50xx 1
Product Overview 2

Shrnutí obsahu

Strany 1 - ABDx-ER-IN50xx

http://www.bb-elec.com/Products/Wireless-Cellular/AirborneM2M-Embedded-Dual-Band-Wireless-Module/AirborneM2M-Embedded-Dual-Band-Access-Point-Module.as

Strany 2 - Product Overview

AMC will display the found Airborne device(s):Connect EthernetAttach the AntennaNote: You may be required to wait up to 180 seconds before the device

Komentáře k této Příručce

Žádné komentáře

Bb-electronics ABDN-ER-IN5018 - Quick Start Guide Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Příslušenství komunikace Bb-electronics ABDN-ER-IN5018 - Quick Start Guide. B&B Electronics ABDN-ER-IN5018 - Quick Start Guide User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Příslušenství komunikace Bb-electronics ABDN-ER-IN5018 - Quick Start Guide